Troy-Bilt String Trimmer Parts | Same Day Shipping (2024)

Troy-Bilt String Trimmer Fuel Tank Assembly W/Fuel Lines Incl. 29

PartSelect Number PS11812933

Manufacturer Part Number 753-06797

The fuel tank assembly is responsible for storing and supplying fuel to the engine in lawn and outdoor power equipment. It includes the tank, fuel cap, and fuel lines. The fuel tank assembly will fail if the tank develops cracks or leaks, or if the fuel lines can become clogged. When the fuel tank assembly fails, you will notice fuel leakage, restricted fuel supply, stalling, difficulties starting and overall lower performance. Before beginning any repairs, first drain any remaining fuel from the tank for your safety. Disconnect the fuel lines from the tank and remove the fuel tank from the equipment. Position the new tank on to the mounting holes and secure it in place. Connect the fuel lines to the engine and vent to complete your repair.

Troy-Bilt String Trimmer Fuel Tank Assembly

PartSelect Number PS10009586

Manufacturer Part Number 753-06183

This fuel tank assembly is supplied by the original manufacturer for use in trimmers. It is responsible for storing and transferring fuel to the engine for combustion. The assembly consists of a plastic tank, a fuel cap, a fuel filter, and the fuel lines which have a diameter of 0.25 inches. If the fuel tank is damaged, or the fuel lines are clogged, the assembly will need to be replaced. A faulty fuel tank assembly will result in fuel leakage, hard starting, rough idling, and poor equipment performance. To begin, drain the fuel from the tank. Disconnect the fuel lines and remove the mounting hardware that secures the assembly to the equipment. Pull off the old assembly and align the new one with the mounting holes. Secure the assembly in place and reconnect the fuel lines. Refill the fuel tank to complete the repair.

Troy-Bilt String Trimmer Line trimmer cutting head assembly

PartSelect Number PS16583608

Manufacturer Part Number 841-013303S

Troy-Bilt String Trimmer Cutting Head Assembly

PartSelect Number PS10009816

Manufacturer Part Number 753-08169

Troy-Bilt String Trimmer Bump Head Knob Assembly

PartSelect Number PS9306452

Manufacturer Part Number 791-153066B

This genuine bump head knob assembly, sometimes known simply as the bump head, is black and approximately 2 inches long. Sold individually, this plastic part releases the cutting line. Over time, this part may break due to wear, and you will know it is broken because it will completely stop functioning. A troubleshooting tip is to tap the part on theg round to see if the cutting line advances. This is an easy repair to make, and does not require any tools. You will need to look for the bump head attachment point on the bottom of the cutting head assembly.

Troy-Bilt String Trimmer Glide Cap

PartSelect Number PS10009817

Manufacturer Part Number 753-08170

This genuine OEM glide cap, is also referred to as a fixed line head. It protects the cutting line of your string trimmer and prevents it from coming into contact with sidewalks or curbs. Housing the cutting head assembly, it guides and helps the trimmer smoothly glide along the edges without causing damage to the line or the machine. The glide cap is typically found at the bottom end of the trimmer head, where the cutting line extends. The cap is made out of plastic and wears out over time, especially when it rubs against the ground. You may also notice that the string feeds outside of the head uncontrollably. To remove the glide cap, simply depress its locking tabs on each side and pull it away from the cutting head. Install the new glide cap by aligning it with the correct notches on the trimmer, pushing it into place, and using a screwdriver to secure the tabs. Please bear in mind that the glide cap is sold separately from the rest of the cutting head assembly.

Troy-Bilt String Trimmer Primer and Hose Assembly

PartSelect Number PS10014772

Manufacturer Part Number 791-683974B

This manufacturer-certified primer and hose assembly includes the primer bulb, the primer bulb housing, and the fuel line. Any or all of the clear plastic parts in this assembly may experience wear and tear over time that cause fuel to leak due to cracking or blockages. If they are not functioning, these parts will fail in their function of supplying fuel from the tank to the carburetor. This is an easy repair, which can be made by identifying the location of the parts, between the fuel tank and the carburetor, and reinstalling them with no special tools required. When installing, make sure the fuel lines are tight to prevent leaks and fire hazards.

Troy-Bilt String Trimmer Fuel Line and Filter

PartSelect Number PS10014709

Manufacturer Part Number 791-682039

This OEM fuel line and filter supply fuel from the tank of your engine to its carburetor. Made of clear plastic and sold individually, the fuel line may end up clogged or cracked, causing fuel to leak as a result of general wear and tear. The filter may also end up damaged or clogged over time, and shold be replaced regularly as a part of proper engine maintenance. Luckily, this is an easy repair that requires no tools to carry out.

Troy-Bilt String Trimmer Bump Head Knob Assembly

PartSelect Number PS10013974

Manufacturer Part Number 791-181468B

This OEM bump head knob assembly, known simply as the bump head assembly sometimes, advances the line on your trimmer in the spool. Black in color, it is made of plastic and steel and is sold individually. Tap your trimmer on the ground to see if the cutting line advances to determine if there is a problem with this part. If it will no longer feed, it is likely that this part needs to be replaced. Most of our customers rated this repair as easy. You can attach your new part to the cutting head with no special tools required to complete the repair.

Troy-Bilt String Trimmer Impeller Assembly

PartSelect Number PS16429077

Manufacturer Part Number 753-08491

This is an impeller assembly kit designed for use with various models of leaf blower and comes with all the hardware necessary to replace it, including the impeller, the securing nut and 1 washer for each side of the impeller. If you notice the blowing power of the leaf blower is reduced or that there is any physical damage to the impeller like bent or cracked blades, the impeller needs to be replaced immediately. When replacing the impeller, you will need a screwdriver or wrench to remove the impeller cover, and you should ensure you use proper safety equipment like gloves.